Remove 10mm nuts on the driver side intake bracket located closer to the fire wall. A slow leak may not be obvious right after install but hopefully it will leak never again!!! Remove all 7 upper intake bolts as listed in the provided All-DATA pages. Oil Filter/Cooler Housing – 68105583AE. PARTS you will need are the oil filter/cooler adaptor as pictured below and intake gaskets. Dorman Replacement Oil Cooler - 3.6. For installation of the new housing follow the provided ALL-DATA pages for proper torque values and patterns. Use dielectric or silicone based lubricant on the injector o-rings to more easily install them, plug injectors back in and seat firmly. I will post as many photos as I can that will aid you, if you choose to tackle the project yourself. Install new oil filter/cooler housing. I would recommend buying new Oil Temp Sensor and new Oil Pressure Sensor. Hear from other customers via the 98 reviews on parts for your Jeep Wrangler.
6L V6 Chrysler 200, Town & Country, Dodge Grand Caravan, Jeep Grand Cherokee, Wrangler, Ram 1500, 2500. Advance Auto Parts has 1 different Engine Oil Filter Housing for your vehicle, ready for shipping or in-store pick up. Genuine Jeep Wrangler Oil Cooler Engine Oil Cooler. Re-install the cooler hose using a standard pliers. Before you unbolt or remove the lower intake, it is important to pry/remove the back wire looms that are secured to the back of the intake. Include vehicles sold in Mexico. It goes at least an inch into the top of engine valley so it may be a little tough. Clean out all old oil from the oil filter/cooler housing mounting valley. Interestingly enough it never overheated, so I pampered it back home and confirmed the leak with a pressure tester. As you can see the bulk of that oil is from the leak itself. It has happened, that is why it's brought up. If you do not have an account but would like to check the status of an order, request a change, or report a problem with an order or shipment, please go to our. Ordered a new Oil cooler assembly using the Dorman aluminum housing that will update the filter to the late style 14 & up. Jeep 3.6 oil cooler upgrade for jeep grand cherokee 2014 limited 4x4. I was lucky to score a NOS transmission and motor off the Bay and promptly returned the Dorman unit.
I also would recommend some masking tape for when the intake is off so you can cover the intake ports to the heads (VERY vulnerable to foreign objects when exposed). This replacement Oil Filter Housing Adapter Kit also comes with a new oil filter pre-installed for a complete and worry free installation. Oil Cooler Housing Upgrades. Product seems way better made than original plastic housing which was leaking oil. The hose is help on by a single clamp that can be removed with pliers. Does anyone make an aftermarket unit that is superior in quality? We offer a full selection of genuine Jeep Wrangler Oil Coolers, engineered specifically to restore factory performance. You will be able to see the general area (top transmission bell housing and behind the engine).
Let me be the first to say, it looks the same. NOTE: After removing the upper intake, I strongly recommend covering the lower intake holes and using an air gun to blow any debris out from the sides of the lower intake. Tools Required: - 8mm Socket. Order Status & Returns.
Before removing the upper intake bolts off, you have to remove the heat shielding pad from behind the engine. Remove upper intake bolts (3- 8mm capture bolts). Carefully pull the blue safety clip from the fuel line and you should be able to squeeze the white clip. Idontknow: As you can also see visible oil near the filter housing. From the TOP of the engine compartment you should be able to see some pooling down in the engine valley where the oil cooler adaptor is located. Remove (2) 10mm heater line mounting nuts. I did not buy OEM intake gaskets. Jeep 3.6 oil cooler upgrade your flash. I have a question: Is there a redesigned or aftermarket/race part that I could use INSTEAD of going back with the dumbf**k plastic part? Once you remove all the bolts, lift up on the upper intake until you feel it free. Confirm New Password. The driver side is very easy, unplug the three injectors on that side, along with the three coil pack wires. Follow all other instructions in reverse order to reassemble your JK. ALL THE PARTS YOUR CAR WILL EVER NEED. Next on the passenger side, remove the two 10mm bolts that holds the bracket onto that side of the intake.
BEFORE pulling the air intake pipe all the way off, disconnect the single sensor located closer the throttle body and behind the pipe (facing the ground/firewall). Fits the following vehicles: Replaces part numbers: 68105583AF, 68105583AE, 68105583AA, 68105583AB, 68105583AC, 68105583AD. Jeep wrangler engine oil cooler. Remove foam on top of driver side spark plugs. Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Remove bracket once both 10mm nuts and bolts have been removed. Pry the two push pins up to detach the pad from the brackets.
I was able to see a little bit of pooled oil looking in between the oil filter housing and the intake. Re-install the fuel rails with driver side first then passenger side. Remove Air Box Components (8mm socket or Flat Tip Screwdriver, 10mm socket, 3″ and 6″ extensions) Including one (1) clip on the bottom of the Air Box hose assembly. The valley is fairly deep as well, so there is quite a bit of oil. Jeep Wrangler Engine Oil Filter Housing | Advance Auto Parts. This is a compatible replacement part manufactured by AA Ignition. There is a neck with an o-ring in the front of the housing. Wide painters take is very effective. I used a brake pump with reservoir to remove the oil from the valley and then used needle noise pliers to dab small pieces of rag and soak up the rest of the oil. By the way 19GCTrailhawk sorry, i meant to give you a like but don't exactly know how it happened it ended up with a instead. The bolts will NOT come all the way out from the actual housing.
Fast and easy service at your home or office. ARNOLT-MG. ASTON MARTIN. Torque Fuel Rails to 62 in lbs. The dealership is around $240. Remove (2) 10mm nuts on driver side rear of upper intake. Torque Sequence (Front #1, Back #2, Middle #3). Atomic: I have an appointment with the dealer to get it fixed, and it's a 100 dollar deductible so it's not a big deal but... Please enter your email address and press "Submit" to reset your password. Once the brackets are removed you can remove the pad and reach the back upper intake bolt easier.
If your leak is as bad as mine was when discovered, you will see motor oil on the bottom of the transmission pan, crossmember, and transfer case. How will you know if your oil cooler is leaking? Maybe a mod here can delete it. Chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm may be present in automotive service, replacement parts and fluids. Yep, cost reduction and in some cases lighter weight.