Your Gas Fireplace Still Won't Stay Lit. Fixing these problems is easy. This involves placing a row of firewood in one direction, and then topping it with another row of firewood running perpendicular to the first. These are some of the common causes that may prevent your fire pit from staying lit. The thermocouple of your fire pit may be at fault in this case. Troubleshooting your Gas Fire Pit. Make sure they aren't too tight, but not overly loose either. Spend time cleaning up the burner ports and removing debris when the pit is not in use. Most ignitors operate with batteries and this is a likely trouble spot. If you are smelling gas, then it's a red alert. If your supply hose needs to be replaced, go ahead and do so!
This will guarantee that the fire burns uniformly and prevent fires and explosions from occurring. Check burner ports and the fuel orifice for blockages and keep them clean. Buying different propane fire pit parts online is the easiest way to get them delivered to your doorstep. You should also examine your burner ports, which can become clogged and dirty. However, for your safety, a local NFI Certified Gas Specialist should always be contacted for further inspection. If you decide to have a gas fire pit, here's an easy guide to learning about the different gas kits available. Immediately Turn Off Gas Supply. If that still does not work, loosen the brass nut that secures the control valve in place, and try again.
Or locate a local NFI Gas Specialist in your region for more troubleshooting information. Once the pilot lights, you should keep depressing the gas valve for at least 10 seconds to give the thermocouple time to warm up. Here are symptoms your propane fire pit is having trouble: - The fire pit burner does not light up. The burner is clogged with debris. Your fire pit will not ignite and stay lit if it has blockages with dirt and debris in the components.
Is it in a place susceptible to wind? With that said, the golden rule of using a fire pit is to place it at least 10 feet away from any flammable or combustible surface, including your home. If you aren't sure, fill the tank or exchange it for a full one. So, press and hold on to the control valve of the fire pit for 10 to 30 seconds. At or below 40ºF propane starts to try to liquefy which will not give a good performance. As this area heats up, it ignites the rest of the firewood. 5 air changes per hour, a table top heater shall not deplete the oxygen level to below 16% by volume, and.
In some cases, it may burn for 10 or 20 minutes. If this is the case, go ahead and replace it. While opening a gas valve, instead of using a lighter you would press and hold the ignition switch. Propane tank fine, fire won't stay lit. Proper storage, under the safeguard of a Fire Pit Cover, ensures the longevity of your investment as it helps protect the fire pit from harmful outdoor elements such as debris, UV sun rays, moisture buildup, and pests. If the unit lights manually, but not with igniter, service or replace igniter switch. If you have trouble, you can turn to the manufacturer's instruction manual for help. The gas line may also get air inside, which causes the fire to flicker from time to time. Disconnect the existing battery and swap it with a new one, ensuring to conserve the precise polarity of the battery. Well, with no further ado, let's get going with our advice below. If your wood fire pit doesn't stay lit, there are mostly a few reasons. If you don't see a spark from the ignition when attempting to light the pilot, release the gas valve immediately and wait five minutes before using another method -- such as a match -- to light it. The new requirement is Consumer Safety Administration (CSA) International Requirement 5. The two important points are you need to ensure enough oxygen flow and heat.
This video sums it up. Those of you who've had the pit for a while should be able to judge how much gas you have in the propane tank simply by lifting the tank. The logs will not change color, but you will notice a carbon build up from propane gas. A professional can assist you in identifying and fixing a faulty gas valve. You can install Cuisinart's CTG 200 In-line Gauge between the firepit and the cut-off valve on the tank. This can happen for several reasons.