It should be something you can keep clean and to which the scotch tape will stick. Firmly stick all of the edges of the tape together and down on the frame of the call. Does he have a website? Go through the cut progression to find that turkey. • small mallet or hammer. The most often mentioned supplier is Pioneer, but there are others as well. Here are a couple angles of the finished product..... Order your materials first. Take one of your frames and bend it at the middle (at the notches) so that you are bending the adhesive-taped side of the "horseshoes" towards each other. This method of call making allows you, the individual, to customize each call you make to your own preferences. Lil jiggy turkey call jig for sale. Here is a video I made showing how to make a call on the "lil jiggy". News: GUESTS ARE WELCOME TO REGISTER TO THE FORUM!!! If you are using the cut reed material and you like backstretch in your calls, you can use small pieces of tape to stretch the back of the reed down to your board to form the "smiley face" some people like. Tips: • Try different latex thicknesses, and in different layers in your calls.
A good standard starting distance is about 1/16" or thereabouts but you can obviously experiment with whatever spacing floats your boat. • call making surface.... a flat, smooth, sanitary surface that scotch tape will stick to. If you guys dont mind, check out some of my other videos on my you tube channel and subscribe.
The tape will have a center cut-out that matches the center reed section of the call. However, if you want to "backstretch" your reeds in the center of the call, you may prefer to use the full latex piece. Again, add backstretch if desired. You can put the edges close together or far apart. For anybody that decides they want to participate in this exercise, get the stuff above and then we can get into the call-making process.... Lil jiggy turkey call building jig for sale online. 12 posts • Page 1 of 1. Thanks in advance for the help.
I finally gave making my own mouth calls a try. You are now ready for setting the tape on your call. I had a broken drafting square laying around and cut it to use here for the latex to lay on while the blocks are required an 1/8" notching on both blocks, when the latex begins to stretch the plastic comes out. Repeat with another reed, if you desire, or go to the frame setting.
You will see multiple colors of latex in the various thicknesses. However, you will have to do this on either side of the center of the reed because if you tape it in the center, it will be in the way of the frame (you will understand this once you start assembling your calls). It is mounted on the block that stays still, not the block that moves. Lil jiggy turkey call building jia yi. Here is what its all retching that latex. I have to run a small frame diaphragm and options are usually pretty limited so I figured I'd try my hand at this call building. Making Calls: The process involves four steps: • reed stretching. 004 thickness or less, down to "proph" which is generally considered to be around. To do this, you will most likely have to slip the scissors between the long reed and the bottom reeds.
Once again, tape both edges of the reed down over the first reed, with whatever stretch and spacing you think you want to try. Most calls have one to three layers of latex of different thicknesses, and are staggered with different spacing along the layered edges of the call. Call frames: I would suggest getting crowned adhesive frames in whatever size(s) you prefer. Here i used a 3/8 fender washer just as added protection to keep the nut from moving, it presses up against the back side of the i turned down a handle and tapped it with a 3/8 thread and glued it up to my all-thread. Turkey hunting forum for turkey hunting tips. As for the actual process, you can build calls without any kind of jig or press very easily, and once you get the hang of it, you will be able to very consistently put together calls that consistently sound great.
Carefully fold the tape down over the call, making sure not to let the tape stick unevenly and create wrinkles in the tape. The deeper the cuts (to a point), the raspier the sound generally will be. To begin with, i took two blocks of wood roughly 2x4x6, and ripped 3/4" off one of my now i have a 2x3. I have put together these written instructions on how to make calls without a press or jig. These are Pioneer products). If you are making a single-reed call, then you will proceed to setting the reed in the frame. It doesn't, pretty much just have to try it and see what works the best for you. On: March 13, 2021, 01:56:57 PM ». Reed material usage: The latex you order will come in 1"X2" pieces (approx.
First of all, you can order the materials for building calls dirt cheap. Now, take the mallet or hammer and tap the horseshoe frame flat along its edges to seal the adhesive to the reeds. In other words, some colors of latex in a specific thickness just seem to make better sounding calls for some reason, obably due to minute differences in the latex sheet properties. Without removing the protective paper on the adhesive side of the tape, fold the tape in the middle (adhesive sides toward each other) and crease it with your fingers so that the center cut-out folds over to create the open area where the latex reeds will sit in the tape. Now, take another small piece of tape and place it on the other short end of the latex reed. Unfold the tape and carefully pull the protective paper back on one side of the fold only. I would advise you to start conservatively with your cuts to see what kinds of sounds you are creating with each cut you add to the call. Of course, you can always order a jig or press, but some are pretty expensive,.. again, for a guy just wanting to build calls for himself and maybe some friends, they are unnecessary. Reply #6 on: March 14, 2021, 10:38:43 AM ». Then i took my other block and cut a 3/4 notch out of it, this is what my peice of 3/4 bar stock mounts on. Bottom line is you can get as many thicknesses/colors as you want to experiment with. I'm going to try to get a video a week with working on my property, drone footage, hunting, fishing and just outdoor related stuff. Long, but hopefully anybody that is interested can wade through it.
There are a variety of frame sizes, tape colors, and reed-material thicknesses and colors, so you can get just about anything you Hunter wrote: ↑ March 13th, 2019, 2:00 pm So if a fella wanted to try his hand at building diaphragm calls, which jig, latex, frames, etc would you recommend purchasing to learn on? Tape: There are multiple colors available. I use a piece of plastic laminate countertop about 6" wide and 2' long for my board, but you can use whatever you wish to use for this. The reed material comes in varying thicknesses and colors.