I'm sure happy I didn't have to buy a new sensor. Near the exhaust, towards the rear of the engine, is where you may find your Duramax turbocharger. Is there a way to clean the vanes without taking it apart? Once you've given the vanes a good clean, reassemble everything and enjoy the boost in performance from your newly cleaned turbocharger! How to Unstick Turbo Vanes Duramax. To my knowledge, there is NOTHING you can "add" to your Turbo to Clean it. How to clean TURBO without removing! Maintaining the performance of your car involves cleaning the turbo vanes on your Duramax engine. So I figured with it seeing dirty exhaust all it's life (and not wanting to spend $400+ on a new sensor) maybe a cleaning would do the job. The procedures you must follow to clean your Duramax turbo vanes without removing them are covered in this article. In some cases, simply cleaning the turbocharger housing and vanes can fix the problem. How to clean turbo vanes duramax without removing them for sale. Once they're all out, inspect them for any damage and replace any damaged ones if necessary. Be sure not to damage the turbine blades! But before unscrewing all the way, I followed the wire to the connecting end.
The turbocharger's vanes must be cleaned after you've found it. Once the sensor was out, I just squirted it was so carburetor cleaner and wiped it down real good. You can keep your turbocharger functioning smoothly and efficiently by according to these instructions. Leaks must be repaired immediately if you find any. How to clean turbo vanes duramax without removing heads. Step 2: Locate the Turbocharger. 99% you won't have to replace it... Other thing is. Next, remove the intake hose from the turbo inlet and use compressed air to blow through the hose. You can reach the vanes once the hose has been taken off. In this blog post, we'll discuss how to clean a variable vane turbo so that it continues to operate at peak performance. Once you've confirmed that the vanes are indeed stuck, it's time to take things apart.
There are a number of reasons why turbo vanes might stick, but the most common cause is deposits on the vane surfaces. Use your rag to wipe the vanes clean once you've finished scrubbing. What Causes Duramax Turbo Vanes to Stick? Protective gloves and eyewear. You can always take your vehicle to a qualified mechanic if you don't feel comfortable handling this procedure. Question: - Turbo Cleaners. This kept the wire from binding up. There are a few ways you can do this, but we recommend using compressed air and a soft brush. I loosened the sensor with a 1" open end wrench and was then able to unscrew by hand. Assuming you would like a blog post discussing how to clean a variable vane turbo: A variable vane turbo, or VVT, is a type of turbocharger that uses vanes to adjust the air flow through the turbine. Locate the turbocharger: The turbocharger is typically located on the exhaust side of the engine and can be identified by the air intake and outlet pipes attached to it. You should notice an immediate difference in performance! Once you have access, use compressed air to blow any dirt or debris out of the vanes. Now attach the air compressor to the injector cleaning kit and turn it on.
Thanks, I would like to avoid paying someone to pull the turbo and or replace it, but am leery of putting anything into the intake that may cause damage. This can cause the engine to lose power and efficiency. How to clean turbo vanes duramax without removing oil. First, remove the intake hose from the turbocharger and disconnect the electrical connector. However, these vanes can become dirty or clogged over time, which can reduce the efficiency of the turbocharger. Use a soft brush to clean off any remaining dirt or debris on the turbocharger blades.
One of the key components of a turbocharger is the turbine, which consists of a series of vanes that spin at high speeds to force air into the engine. On the very tip I did notice a "wear line" and it seemed just fine. Inspect the turbocharger for any visible dirt or debris and remove if necessary. And if you do so, chances are 99. Wait for the degreaser to take effect: Allow the degreaser to sit for a few minutes to loosen and dissolve any dirt and grime on the turbocharger. Make sure everything is functioning properly by letting the engine run for a few minutes. They will set a couple of codes every time they go through a self diagnostics cycle.
They allow engines to produce more power by forcing more air into the cylinders. I am not enough of a mechanic to tear into it myself. Finally, reconnect everything and start your engine. When these deposits build up on the vanes, they prevent them from spinning freely, causing a loss of performance. With proper care and maintenance, your variable vane turbo should give you years of trouble-free operation! Credit: How Do You Clean Turbo Vanes Without Removing Them? This allows for more precise control of the boost pressure, and can improve fuel economy and performance. I removed that end from it's mount, secured by two blue plastic clips (I just cut the ends of mine with a pair of *****) and unplugged the harness. To start the engine, identify the turbocharger, clean the vanes, reattach the intake hose, and check for leaks, don't forget to use turbo cleaner. The first step is to remove any dirt or debris from the outside of the turbocharger. Check for leaks and ensure the intake hose is tightly fastened. This increased air density means that more fuel can be burned, resulting in more power.
I snugged it back with the wrench and plugged the harness back in. Note: Take caution when working on the engine, as some parts may be hot and could cause injury. You should hear a whooshing sound as the air passes through; if not, then there's a good chance that your vanes are still stuck. Any remaining particles that could be in the turbocharger will be blown out by doing this. Reinstalling the intake hose is required after you have completed cleaning the vanes. The turbocharger and intake are connected via this hose.